23 replies to this topic

[jakAtariTech]

Hello for all, i buy a atari jaguar and atari jaguar cd on ebay, but i dont can do work jaguar cd,

the jaguar base whith cartridge are good

the jaguar cd with cartridge are good too

but when i power on without cartridge only with cd , always see the same picture of back to console and NO POWER, but i use the originals official power supply!!

i open totally console, clean contact intern and extern of jaguar and jaguar cd, i check all , but I CANT FIX THIS!!!!!! PLEASE HELP MEEEEE I PAY 300$ and i feel VERY BAD!!!

plese help me!!!!! atach image of my error!!

Attached Thumbnails

• 

Edited by jakAtariTech, Thu May 26, 2011 11:58 AM.

[sh3-rg]

Have you tried powering the Jaguar on its own with just the power pack form the jag CD?

[the.golden.ax]

One of your power supplies is either not working or not giving enough power to the CD drive. Try switching the power cords from one unit to the other. If the Jaguar will not boot up with both of the power supplies you may need a new one.

AX

[jakAtariTech]

hello , in first say thanks very much for help me to fast!!!

i try conect just jaguar cd but in this mode atari jaguar base led not light and dont work

the jaguar adapters are totally functionally (i have 3 official power supply) , and the 3 adapters are work into the base console but non workin into jag cd

any solutions??? thaaaaaaaaaaaaaaaaaaaaaaaaaaaanksss

Edited by jakAtariTech, Thu May 26, 2011 1:05 PM.

[BuddyBuddies]

there has to be a game in the Jaguar console for the power to come on, not sure if you knew that already. Good luck

[jakAtariTech]

BuddyBuddies, on Thu May 26, 2011 1:56 PM, said:

there has to be a game in the Jaguar console for the power to come on, not sure if you knew that already. Good luck

hello when you use a cd in jaguar cd dont can put any cartridge because if you put any cartridge the consolo run a cartridge non cd game, i need good luck!!!!!!!!!!!!!!!!

thanks al lot friend for your solution but my jaguar problem dont fix!!! thaaaanks

[WIZZARD77]

Check the solder points for the power connector on the JagCD board. Could just be a bad connection there.

[jakAtariTech]

WIZZARD77, on Thu May 26, 2011 2:44 PM, said:

Check the solder points for the power connector on the JagCD board. Could just be a bad connection there.

hello, this point are test with my tester


anybody have this problem??? im Alone whit this problem??? unbelive!!!

but thanks very much,


i try whit power supllpy with more amper and dont work

Edited by jakAtariTech, Thu May 26, 2011 3:00 PM.

[the.golden.ax]

Make sure it has the correct polarity.

AX

[jakAtariTech]

the.golden.ax, on Thu May 26, 2011 3:22 PM, said:

Make sure it has the correct polarity.

AX

yes its a correct polarity, its a official power supply!! thanks

[busterm]

Ive had this happen a few times on some Jaguar CD's I've refurbished most of the time the CD motor on the Transponder is burned out or one of the solder points on the transpond motor or laser has come loose. You will notice there are small cables that go with it.

That icon you see means power isnt being received by one of the Jaguar CD components not just the Jaguar CD itself.

Edited by busterm, Thu May 26, 2011 5:21 PM.

[jakAtariTech]

busterm, on Thu May 26, 2011 5:20 PM, said:

Ive had this happen a few times on some Jaguar CD's I've refurbished most of the time the CD motor on the Transponder is burned out or one of the solder points on the transpond motor or laser has come loose. You will notice there are small cables that go with it.

That icon you see means power isnt being received by one of the Jaguar CD components not just the Jaguar CD itself.

hello, when i put the laser in the up zone (with my hands) and power on the console, this motor are ok and go a laser down, is this possible with cd motor broken??? i check every point of solder of a len and motor and i dont see any damage point, what point are you think maybe damage, i can try check again this point, thanks a lot friend.

[the.golden.ax]

jakAtariTech, on Thu May 26, 2011 3:28 PM, said:

the.golden.ax, on Thu May 26, 2011 3:22 PM, said:

Make sure it has the correct polarity.

AX

yes its a correct polarity, its a official power supply!! thanks

I meant when you try a power supply with more mAh

AX

[busterm]

jakAtariTech, on Thu May 26, 2011 6:03 PM, said:

busterm, on Thu May 26, 2011 5:20 PM, said:

Ive had this happen a few times on some Jaguar CD's I've refurbished most of the time the CD motor on the Transponder is burned out or one of the solder points on the transpond motor or laser has come loose. You will notice there are small cables that go with it.

That icon you see means power isnt being received by one of the Jaguar CD components not just the Jaguar CD itself.

hello, when i put the laser in the up zone (with my hands) and power on the console, this motor are ok and go a laser down, is this possible with cd motor broken??? i check every point of solder of a len and motor and i dont see any damage point, what point are you think maybe damage, i can try check again this point, thanks a lot friend.

Their are two motors
one turns the cd which is the one that goes out the most often and the second smaller one that moves the laser back and forth

[jakAtariTech]

i try with a universal adapter with 2000 mha and nothing !!!


i check wires of two motors and i cant see any broken wire or anything bad!! pfff

[jakAtariTech]

i take a photos

Attached Thumbnails

• 

Edited by jakAtariTech, Thu May 26, 2011 6:53 PM.

[FABombjoy]

I've also seen that screen come up when there is a bad connection on the cartridge interconnect board in the Jag CD unit. Twice, actually. Removing, cleaning, and reseating that board fixed it both times.

[JagChris]

Something the actual Jaguar CD lid doesnt seat right on that little switch that is suppose to let it know the CD lid is closed. Close the Jag CD lid and try making sure it is seated securely. Or hold the switch down manually and see if that is the problem.

[jakAtariTech]

the cartridge pin an every pins conector intern an extern are cleaned, the switch you say jagchris are good i tested this whith a tester, i hold the swith of cd open and dont worry, pfffff thanks friends

[jakAtariTech]

can this problem of this??? how i test this??

Attached Thumbnails

• 

[JagChris]

jakAtariTech, on Fri May 27, 2011 12:20 PM, said:

the cartridge pin an every pins conector intern an extern are cleaned, the switch you say jagchris are good i tested this whith a tester, i hold the swith of cd open and dont worry, pfffff thanks friends

ok just trying to cover all bases.

[JagChris]

jakAtariTech, on Fri May 27, 2011 12:32 PM, said:

can this problem of this??? how i test this??

When you post stuff like this you might want to take a moment with MS Paint or somesuch and circle the actual area you are specifically curious about. All we see is a long splaying circuitboard.

[jakAtariTech]

ok, sorry , this regulators

Attached Thumbnails

• 

[busterm]

From the photo they look fine. As for the motors you wont know if they are dead or not till you supply power to them. If the CD lens moves back and forth when you power on the Jaguar but the cd spindle motor does not move then the motor for the spindle is confirmed dead.